Jotrin Electronics
Корзина
Описание Количество Общий (USD) Операция
loading

Корзина продуктов : 0
Дома > Other > Analysis of the role of matching resistors in PCB design

Analysis of the role of matching resistors in PCB design

Время публикации: 2019-10-07

1. Impedance matching

Impedance matching refers to a suitable matching method between a signal source or a transmission line and a load. According to the access mode, the impedance matching has two modes: serial and parallel; according to the signal source frequency impedance matching, it can be divided into low frequency and high frequency.

(1) High frequency signals generally use serial impedance matching.

The resistance of the serial resistor is 20~75Ω. The resistance value is proportional to the signal frequency and inversely proportional to the PCB trace width. In embedded systems, serial matching resistors, such as clock signals, data, and address bus signals, are added to the system when the signal is greater than 20M and the PCB trace length is greater than 5cm. There are two functions of serial matching resistors:

◆ Reduce high frequency noise and edge overshoot

If the edge of a signal is very steep, it contains a lot of high-frequency components, which will cause radiation interference, and it is also prone to overshoot. The series resistor and the distributed capacitance of the signal line and the load input capacitance form an RC circuit, which reduces the steepness of the signal edge.

 resistor

◆ Reduce high frequency reflection and self-oscillation

When the frequency of the signal is high, the wavelength of the signal is very short. When the wavelength is short compared with the length of the transmission line, superimposing the reflected signal on the original signal will change the shape of the original signal. If the characteristic impedance of the transmission line is not equal to the load impedance (ie, it does not match), a reflection will occur at the load end, causing self-oscillation. The low-frequency signals of the traces in the PCB board can be directly connected, and it is generally unnecessary to add a serial matching resistor.

(2) Parallel impedance matching, also called "terminal impedance matching"

It is generally used at the input/output interface end, mainly referring to the impedance of the transmission cable. For example, the input matching resistance of the LVDS and RS422/485 using Category 5 twisted pair is 100~120Ω; the matching resistance of the video signal using the coaxial cable is 75Ω or 50Ω, and the flat cable is 300Ω. The resistance of the parallel matching resistor is related to the medium of the transmission cable, and has nothing to do with the length. Its main function is to prevent signal reflection and reduce self-oscillation.

It is worth mentioning that impedance matching can improve the EMI performance of the system. In addition, in addition to the use of series/parallel resistance, impedance matching can be used to perform impedance transformation. Typical examples are Ethernet interface, CAN bus, etc.

2, the role of 0 ohm resistor

(1) The simplest is to use the jumper. If a certain line is not used, the resistor can be directly soldered (without affecting the appearance).

(2) When the matching circuit parameters are uncertain, replace them with 0 ohms. When the actual debugging is performed, determine the parameters and replace them with specific numerical components.

(3) When you want to measure the working current of a certain part of the circuit, you can remove the 0 ohm resistor and connect the ammeter to make it easy to measure the current.

(4) When wiring, if the actual cloth is not passed, you can also add a 0 ohm resistor to bridge the effect.

(5) In the high-frequency signal network, act as an inductor or capacitor (impedance matching, 0 ohm resistor also has impedance!). When used as an inductor, it is mainly to solve the EMC problem.

 resistor

(6) Single-point grounding, for example, a single point of analog ground and digital ground.

(7) The configuration circuit can replace the jumper and the DIP switch. Sometimes the user will tamper with the settings, which may cause misunderstanding. In order to reduce the maintenance cost, the 0 ohm resistor is used instead of the jumper to solder on the board.

(8) For system debugging, for example, the system is divided into several modules. The power supply between the modules is separated from the ground by a 0 ohm resistor. When the power supply or ground is shorted during the debugging phase, the 0 ohm resistor can be removed to narrow the search range.

The above functions can also be replaced with "magnetic beads". Although the 0-ohm resistor and the magnetic bead are similar in function, there are essential differences, the former is impedance characteristic, and the latter is inductive. Magnetic beads are generally used in power and ground networks for filtering.

 

Мой счет

Email:

sales@jotrin.com

Skype:

jotrin03

Телефон:

86-755-83666342

Live Chat